| View previous topic :: View next topic |
| Author |
Message |
mikezilla2
Status: Offline
Joined: 12 Jun 2007
Posts: 5236
$poons: 588.60
|
 Posted: Sat Feb 04, 2012 10:11 pm Post subject: motion joy and dolphin |
|
|
 |
|
just thought i would ask im not srue what sensitive ti should run with for the analogues dead zones are pretty far and wide in twin snakes
_________________
|
|
| Back to top |
|
|
Pagan's Mind
Status: Offline
Joined: 19 Jun 2009
Posts: 2900
$poons: 4.40
Location: Gold Coast
|
| Posted: Sat Feb 04, 2012 10:44 pm Post subject: |
|
|
|
|
|
You can change the deadzone under the control options in Dolphin. There's a graph thingy that shows you the sensitivity and deadzone. I have mine set to 16 on both sticks. It really depends on how worn in the controller is though as after a while the sticks become loose.
|
|
| Back to top |
|
|
mikezilla2
Status: Offline
Joined: 12 Jun 2007
Posts: 5236
$poons: 588.60
|
| Posted: Sun Feb 05, 2012 2:17 am Post subject: |
|
|
|
|
i don't no i haven't quite found that sweet spot yet ...
_________________
|
|
| Back to top |
|
|
Pagan's Mind
Status: Offline
Joined: 19 Jun 2009
Posts: 2900
$poons: 4.40
Location: Gold Coast
|
| Posted: Sun Feb 05, 2012 2:38 am Post subject: |
|
|
|
|
You could buy the Xbox 360 controller for Windows  . It's basically plug and play after you installed the driver, no need for needless configuration menus like motionjoy. Still gotta configure it for Dolphin though...
|
|
| Back to top |
|
|
mikezilla2
Status: Offline
Joined: 12 Jun 2007
Posts: 5236
$poons: 588.60
|
| Posted: Sun Feb 05, 2012 2:43 am Post subject: |
|
|
|
|
never ! nah i have an old sixaxis so might as well use that .... whats a good setting for the sensitivity ? and its represented by ?
_________________
|
|
| Back to top |
|
|
mikezilla2
Status: Offline
Joined: 12 Jun 2007
Posts: 5236
$poons: 588.60
|
| Posted: Tue Feb 07, 2012 12:34 am Post subject: |
|
|
|
|
cheers for the help everyone , pushing 60+ FPS for gameplay ( dipping at around 50 - 55 ) and about 70 odd FPS on codec screens + some gameplay sections audio dosnt cut anymore ether and its interesting to see that DX11 works almost as well as DX9 if not better its just got a pretty bad glitch ( pretty much massvie tears of what looks like your GFX card dying ) but yea for anyone wondering give it a try - i cant seem to be able to look up or down when in the ventilation shafts tho
any who remember to save as its tends to crash after about an hour if it gobbles up all your ram ( no duh)
oh running on rev 3.0-373 the current one dosnt have the massive glich that i spoke of but has really bad slow down.
_________________
|
|
| Back to top |
|
|
Celtcry
Status: Offline
Joined: 11 Feb 2012
Posts: 1
$poons: 0.00
|
| Posted: Sat Feb 11, 2012 9:36 pm Post subject: How to configure motioninjoy PS3 controller with Dolphin 3.0 |
|
|
|
|
I am trying to configure Motioninjoy with a Ps3 controller to play Resident Evil Zero with the Dolphin emulator. I tried the "Load Diver" trick and set the 360 and PS3 setting (all configured buttons).
I can configure all the controller pads in Dolphin GC configuration controller but when I load the game, it is unresponsive. I cannot format the memory card because the controller does not response. How can I configure it to work?
EDIT: Nvm that, I just figure it out.
|
|
| Back to top |
|
|
|
